• Your shopping cart is empty!

Turbo Oil Fuel Hose Line Kit, Oil Feed and Return For 1st Gen. Mazda RX-7 SA/FB with 13B Turbo Motor, Stock Turbo

This Kit Provides All the Necessary Fittings and Oil Lines to Plumb Oil for Stock Turbo, from Engine Block to Turbo and Back to Oil Pan

Note: 

ONLY Fits SA/FB Chassis with 13B Turbo Motor. Does NOT Fit 2nd and 3rd Gen FC/FD Chassis with 13B Turbo Which Uses Different Front Cover. It Uses Different Oil Return. We Offer This Kit with Other Listing.

This kit Comes with:

- 24" AN4 Stainless Steel Braided Oil Feed Line x1

- Oil Return Line AN10 24" Long x1

- AN4 Oil Feed Flange Adaptor To Turbo x1

- AN4 Oil Fitting From the Block x1 (Need to Re-Use Factory Banjo Bolt)

- AN10 45 Degree Reusable Hose End Oil Fitting x1

- AN10 Straight Reusable Hose End Oil Fitting x1

- AN10 Turbo Oil Return Flange x1

- AN10 Oil Pan Drain Return Plug x1 (Need to Drill A Hole on Front Cover for Oil Return)
　

Write a review

Please login or register to review

Turbo Oil Fuel Hose Line Feed Drain Return Hose Kit For Mazda RX7 RX-7 SA FB 13B AN10

  • Brand: CXRacing
  • Product Code: OIL-KIT-13B-FB
  • Availability: In Stock

  • $122.00


0 reviews / Write a review

Tags: Turbo Oil Fuel Hose Line Kit, Oil Feed and Return For 1st Gen. Mazda RX-7 SA/FB with 13B Turbo Motor, Stock Turbo This Kit Provides All the Necessary Fittings and Oil Lines to Plumb Oil for Stock Turbo, from Engine Block to Turbo and Back to Oil Pan Note: ONLY Fits SA/FB Chassis with 13B Turbo Motor. Does NOT Fit 2nd and 3rd Gen FC/FD Chassis with 13B Turbo Which Uses Different Front Cover. It Uses Different Oil Return. We Offer This Kit with Other Listing. This kit Comes with: - 24" AN4 Stainless Steel Braided Oil Feed Line x1 - Oil Return Line AN10 24" Long x1 - AN4 Oil Feed Flange Adaptor To Turbo x1 - AN4 Oil Fitting From the Block x1 (Need to Re-Use Factory Banjo Bolt) - AN10 45 Degree Reusable Hose End Oil Fitting x1 - AN10 Straight Reusable Hose End Oil Fitting x1 - AN10 Turbo Oil Return Flange x1 - AN10 Oil Pan Drain Return Plug x1 (Need to Drill A Hole on Front Cover for Oil Return)



Emission Notes:

All Parts and services offered by CX-GARAGE are for competition vehicles only. Use on State and Federal Highways may be a violation of the EPA Clean Air Act. The Clean Air Act can be found at http://www.epa.gov/air/caa/. This document contains in detail what are considered to be violations of the CAA and corresponding penalties for failure to obey and should be read in full before purchasing or installing this competition use only product. Ensuring that all emissions, noise/sound, and speed/use related laws are followed is the responsibility of the Buyer(s). Installation and use of this product indicates that this disclaimer has been read, acknowledged, and understood fully by both the Buyer(s) and Installer(s). The Buyer(s) assumes all associated risk of the purchase.

Federal and several state laws prohibit the removal, modification or rendering inoperative of any part that affects emissions or safety on motor vehicles used on public streets or highways. CX-GARAGE assumes no liability for any violations arising out of any federal, state or provincial emissions or safety requirements on motor vehicles arising out of the customer’s modifications and/or use of CX-GARAGE products. It is the responsibility of the customer to determine if their modified vehicle complies with applicable laws.
Proposition 65 Warning:

These products may contain chemicals known to the State of California to cause birth defects or other reproductive harm. For more information visit www.P65Warnings.ca.gov.